SAIVS
  • HOME
  • ABOUT US
    • Honor
    • Manufacturing Capacity
    • Privacy Policy
    • Terms of Service
    • FAQ
  • PRODUCTS
    • Hydraulic Pumps
      • Rexroth
        • A2F Series
        • A4 F/V Series
        • A7VO Series
        • A8VO Series
        • A10V Series
        • A11V Series
        • PG Series
        • AZ Series
        • PV Series
      • Parker
        • PV-plus Series
        • P1 PD Series
        • PAVC Series
        • VP1 Series
        • PG Series
        • P2 P3 Series
      • Sauer-Danfoss
        • 45 Series
        • 90 Series
      • Eaton Vickers
        • PVM Series
        • PVH Series
        • PVQ Series
        • PVE Series
        • VMQ Series
      • Nachi
        • PVD Series
        • PVK Series
        • PVS Series
        • PZS Series
        • PZ Series
      • Hawe
        • V30 Series
        • V60N Series
      • Kawasaki
        • K3V Series
        • K5V Series
      • Sumitomo
        • QT Series
      • Linde
        • MPR Series
        • HPV-02 Series
        • HPR-02 Series
      • Vane Pumps
      • Gear Pumps
    • Hydraulic Motors
      • SAI GM Series Motor
      • Intermot Piston Motor
      • Hydraulic Cycloidal Motors
      • Rexroth Hydraulic Motor
      • Poclain Hydraulic Motor
    • Hydraulic Valves
      • Pressure Relay
      • Pressure Valve
      • Threaded Cartridge Valve
      • Flow Valve
      • Anti-explosion Valve
      • Proportional servo valve
      • Direction Valve
      • Directional Control Valves
    • Planetary Gearboxes
      • Rexroth
      • Bonfiglioli
      • Brevini
      • Dinamicoil
      • O&K
    • Hydraulic Cylinder
      • Aerial Work Platforms
      • Agricultural Equipment
      • Construction Equipment
      • Manufacturing Equipment
      • Marine
      • Material Handling
      • Mining
      • Road Service
      • Waste/Recycling
      • Cylinder Parts
    • Hydraulic Power Units
      • Scissor High Altitude Platform
      • Pallet Car
      • The Wing Car
      • Lift Platform
      • Automobile Tail Plate
      • Special Vehicle
    • Hydraulic Pump Parts
      • Parker Series
      • Komatsu Excavator Series
      • Hitachi Series
      • Rexroth Series
      • Sauer Danfoss Series
      • Uchida Series
      • Messori Series
      • Kayaba Series
      • Toshiba Series
      • Nachi Series
      • Eaton Vickers Series
      • Linde Series
      • Caterpillar Series
      • Kawasaki Series
      • Kobelco/Kato Series
      • Hawe Series
      • Sumitomo Series
    • Hydraulic Tools
      • Flange Tools
      • Hydraulic Lifting tools
        • Hydraulic pump
        • Hydraulic Cylinder/Jack
        • Hydraulic Professional Tools
      • Bolting Tools
        • Hydraulic Tensioners
        • Hydraulic Torque Wrench Pumps
        • Torque wrenches
      • Hydraulic Components
      • Electric Power Tools
    • Hydraulic System
    • Hydraulic Manifolds
    • Hydraulic Winch
    • Electro Hydraulic Actuators
  • APPLICATIONS
    • MOBILE
    • AGRICULTURE
    • INDUSTRIAL
    • ENERGY
    • FOOD & BEVERAGE
    • OIL & GAS
  • DOWNLOAD
    • Best PDF
  • CONTACT US
  • BLOG
HOME > BLOG

Tackling Oil Trapping and Imbalance in Gear Pumps

Author:SAIVS Time:2024-10-12 Click:

As a core component of Hydraulic Systems, gear pumps are widely used in various industrial applications. However, during the operation of gear pumps, issues such as oil trapping and radial imbalance forces often affect their efficiency and service life. If left unaddressed, oil trapping can cause the oil temperature to rise, increase noise, and lead to cavitation. On the other hand, radial imbalance forces can exacerbate component wear, shortening the pump's lifespan. Therefore, implementing effective optimization designs to address these issues is key to ensuring the stable operation of gear pumps.

To optimize the performance of gear pumps, the following improvements can be made to mitigate oil trapping and radial imbalance forces:

Optimization of Oil Trapping

During gear pump operation, oil trapping leads to instantaneous high pressure as the trapped oil is compressed, causing changes in sealed volume that result in cavitation, overheating, and additional impact loads on parts. To reduce the negative effects of oil trapping, the following optimization measures should be taken:

Relief Groove Design: A well-designed relief groove should be added to the side covers of the gear pump. When the sealed volume decreases, the right relief groove should communicate with the discharge chamber, and when the sealed volume increases, the left relief groove should connect to the suction chamber. The spacing between the two relief grooves must be precisely designed to prevent any connection between the suction and discharge chambers, thus avoiding oil trapping.

Pressure Balance Channels: By introducing special pressure relief channels in the trapped oil area, the trapped oil can release pressure promptly, reducing oil temperature and impact loads. This also helps minimize cavitation and noise, thereby improving system stability and extending the pump's lifespan.

HYVA-hydraulic-gear-pumps-saivs-13.webp

Optimization of Radial Imbalance Forces

Radial imbalance forces arise in gear pumps due to uneven pressure distribution of the oil, which can lead to shaft bending, gear wear, and accelerated bearing damage. To effectively reduce the impact of radial imbalance forces, the following optimization measures can be adopted:

Narrowing the Discharge Port: By reducing the range of the discharge port, the high-pressure chamber’s effect is limited to one or two gear teeth, which reduces the radial imbalance force acting on the gears and shaft. This, in turn, lowers the pressure of the gear tip on the stator.

Increasing Radial Clearance: Increasing the radial clearance between the gear teeth and the inner surface of the stator prevents direct metal contact, reducing wear and extending the pump's service life.

Using Needle or Roller Bearings: To enhance bearing load capacity and reduce wear, it is recommended to use needle or roller bearings instead of conventional plain bearings, which can better handle radial imbalance forces.

Conclusion

By optimizing oil trapping and radial imbalance forces, significant improvements can be achieved in reducing gear pump noise, vibration, and cavitation. These enhancements not only improve volumetric efficiency and service life but also contribute to the overall stability of the hydraulic system, extending the lifespan of the equipment.

Tag: gear pump

Random Recommend

  • Understanding and Repairing Single-Acting Hydraulic Cylinders
  • How to ensure the excellent sealing performance of the oil cylinder
  • the precautions for installation of hydraulic components
  • What is the function of hydraulic oil pump in mining production?
  • Bolting Safety Revolutionized: Washer System Eliminates Hand Injuries
  • Log No. 16:Hollow torque wrenches To Taiwan Customer
  • A Modern Approach to Large-Tonnage Cylinder Repair
  • Daily check and maintenance of hydraulic solenoid valves, effective service life!
  • Overview of Leading Hydraulic Motor Brands and Their Applications
  • Operation of the hydraulic motor of the electrohydraulic pump

Related Products

EM56 TRAVEL MOTOR

EM56 TRAVEL MOTOR

Kawasaki Series Hydraulic Pump K3V/K5V/K7V Parts With Spare Parts Repair Kit

Kawasaki Series Hydraulic Pump K3V/K5V/K7V Parts With Spare Parts Repair Kit

HPV116/145/125B

HPV116/145/125B

2500 Nm,M30-M33,Electric Torque Multiplier

2500 Nm,M30-M33,Electric Torque Multiplier

PE15 PE25 Series Oil Gear Electric Pump

PE15 PE25 Series Oil Gear Electric Pump

P40,1 Spool,10.6 GPM,Hydraulic Directional Control Valves

P40,1 Spool,10.6 GPM,Hydraulic Directional Control Valves

SJF Series Double-Acting High Tonnage Cylinders Lift Jack

SJF Series Double-Acting High Tonnage Cylinders Lift Jack

BRL100 SAUER 90 Hydraulic Replacement Spare Parts

BRL100 SAUER 90 Hydraulic Replacement Spare Parts

HPD, 100-200 Ton, Clamp Rail Type Synchronous Pushing Hydraulic System

HPD, 100-200 Ton, Clamp Rail Type Synchronous Pushing Hydraulic System

Torque Socket for Wrench SE Series

Torque Socket for Wrench SE Series

  • ABOUT US

    • Honor
    • Manufacturing Capacity
    • Privacy Policy
    • Terms of Service
    • FAQ
  • PRODUCTS

    • Hydraulic Pumps
    • Hydraulic Motors
    • Hydraulic Valves
    • Planetary Gearboxes
    • Hydraulic Cylinder
    • Hydraulic Power Units
    • Hydraulic Pump Parts
    • Hydraulic Tools
    • Hydraulic System
    • Hydraulic Manifolds
    • Hydraulic Winch
    • Electro Hydraulic Actuators
  • APPLICATIONS

    • MOBILE
    • AGRICULTURE
    • INDUSTRIAL
    • ENERGY
    • FOOD & BEVERAGE
    • OIL & GAS
  • CONTACT US

    NO. 626 Yuncai Road,

    Yunlong Town, Yinzhou,

    Ningbo, Zhejiang, China.

    +86-574-88188161
    +8613905748980

    Monday - Friday:

    8:30 AM to 5:30 PM

    seo1@saivs.com

    Saivs industrial twitter youtube linkedin pinterest
Copyright © 2012-2025 Ningbo Saivs Machinery Co.,ltd. 
TAGS  SiteMap