SAIVS
  • HOME
  • ABOUT US
    • Honor
    • Manufacturing Capacity
    • Privacy Policy
    • Terms of Service
    • FAQ
  • PRODUCTS
    • Hydraulic Pumps
      • Rexroth
        • A2F Series
        • A4 F/V Series
        • A7VO Series
        • A8VO Series
        • A10V Series
        • A11V Series
        • PG Series
        • AZ Series
        • PV Series
      • Parker
        • PV-plus Series
        • P1 PD Series
        • PAVC Series
        • VP1 Series
        • PG Series
        • P2 P3 Series
      • Sauer-Danfoss
        • 45 Series
        • 90 Series
      • Eaton Vickers
        • PVM Series
        • PVH Series
        • PVQ Series
        • PVE Series
        • VMQ Series
      • Nachi
        • PVD Series
        • PVK Series
        • PVS Series
        • PZS Series
        • PZ Series
      • Hawe
        • V30 Series
        • V60N Series
      • Kawasaki
        • K3V Series
        • K5V Series
      • Sumitomo
        • QT Series
      • Linde
        • MPR Series
        • HPV-02 Series
        • HPR-02 Series
      • Vane Pumps
      • Gear Pumps
    • Hydraulic Motors
      • SAI GM Series Motor
      • Intermot Piston Motor
      • Hydraulic Cycloidal Motors
      • Rexroth Hydraulic Motor
      • Poclain Hydraulic Motor
    • Hydraulic Valves
      • Pressure Relay
      • Pressure Valve
      • Threaded Cartridge Valve
      • Flow Valve
      • Anti-explosion Valve
      • Proportional servo valve
      • Direction Valve
      • Directional Control Valves
    • Planetary Gearboxes
      • Rexroth
      • Bonfiglioli
      • Brevini
      • Dinamicoil
      • O&K
    • Hydraulic Cylinder
      • Aerial Work Platforms
      • Agricultural Equipment
      • Construction Equipment
      • Manufacturing Equipment
      • Marine
      • Material Handling
      • Mining
      • Road Service
      • Waste/Recycling
      • Cylinder Parts
    • Hydraulic Power Units
      • Scissor High Altitude Platform
      • Pallet Car
      • The Wing Car
      • Lift Platform
      • Automobile Tail Plate
      • Special Vehicle
    • Hydraulic Pump Parts
      • Parker Series
      • Komatsu Excavator Series
      • Hitachi Series
      • Rexroth Series
      • Sauer Danfoss Series
      • Uchida Series
      • Messori Series
      • Kayaba Series
      • Toshiba Series
      • Nachi Series
      • Eaton Vickers Series
      • Linde Series
      • Caterpillar Series
      • Kawasaki Series
      • Kobelco/Kato Series
      • Hawe Series
      • Sumitomo Series
    • Hydraulic Tools
      • Flange Tools
      • Hydraulic Lifting tools
        • Hydraulic pump
        • Hydraulic Cylinder/Jack
        • Hydraulic Professional Tools
      • Bolting Tools
        • Hydraulic Tensioners
        • Hydraulic Torque Wrench Pumps
        • Torque wrenches
      • Hydraulic Components
      • Electric Power Tools
    • Hydraulic System
    • Hydraulic Manifolds
    • Hydraulic Winch
    • Electro Hydraulic Actuators
  • APPLICATIONS
    • MOBILE
    • AGRICULTURE
    • INDUSTRIAL
    • ENERGY
    • FOOD & BEVERAGE
    • OIL & GAS
  • DOWNLOAD
    • Best PDF
  • CONTACT US
  • BLOG
HOME > BLOG

Instructions for disassembly and assembly of hydraulic motors

Author:SAIVS Time:2022-09-02 Click:

The clearance of each moving pair of the motors delivered by talems hydraulic has been matched, and users are not allowed to replace parts at will. Under normal circumstances, do not disassemble the motor at will. Only in case of serious failure can the motor be disassembled and inspected with the consent of our company.

Instructions for disassembly and assembly of hydraulic motor.jpg

(1) Preparation before disassembly


1 remove the oil drain plug and drain the oil in the motor housing.

2 loosen the 5 screws on the oil pan and remove the oil pan.

3 take out the oil distribution plate, locating ring, cushion block, cylindrical pin and double headed key.

Note: in order to prevent the change of rotation direction after reassembly, the end face of the output shaft and the surface of the oil distribution plate must be marked in the same direction.

(2) Disassembly and assembly sequence

1 remove the cover, screw the clean screw into the central screw hole of the crankshaft, and lift out the crankshaft.

2 remove the snap ring on the connecting rod.

3 take out the assembly of the connecting rod of the plunger body and make corresponding marks one by one, so that the original clearance can be guaranteed during reassembly. Generally, the user can check and repair the plunger body and connecting rod after disassembling it here. If necessary, the assembly of the plunger body and connecting rod can be disassembled: loosen the spring retaining ring for the hole, take out the retaining ring, and the plunger body and connecting rod can be separated.

4 assemble according to the reverse procedure above, and pay attention to ensuring the axial clearance of the bearing.

5 all parts must be cleaned before assembly to avoid scratching or bumping any working surface.

6 if only the sand hole of the plunger sleeve leaks oil or the joint surface of the plunger sleeve and the shell leaks oil, loosen the screw on the plunger sleeve, remove the plunger sleeve, and replace the plunger sleeve or "O" ring.


Easy problems of Hydraulic Motor, cause analysis and troubleshooting


Serial number:

Fault phenomenon

Cause analysis

Exclusion method:


The rotation is opposite to the predetermined direction


Reverse installation of oil distribution plate

Remove the oil distribution plate, take out the oil distribution plate, rotate it 180 degrees, and then reinstall it.


1. Faults in other parts of the system

Check the system and eliminate it.


The rotation speed decreases and the operation is abnormal, and the output torque decreases.

2. Serious external leakage of motor


1. Check the contact surface between the oil pan and the housing; 2. Check the seals between the parts; 3. Check the viscosity of the hydraulic oil and the working oil temperature; 4. Check the wear of the parts of the moving pair


3. Large leakage in the motor


1. Check the wear of the sealing ring on the oil distribution plate 2. Check the wear of the oil passage plate and check whether the two oil chamber channels at the inlet and outlet of the casting are connected.


The motor does not rotate and the pressure does not go up


1. Faults of other parts of the system 2. Broken double headed key


1. Check the system and eliminate it. 2. Remove the oil pan and oil distribution pan and replace the parts.


The motor does not rotate and the pressure increases


1. Some moving pairs inside the motor bite each other; 2. The load exceeds the set value

Disassemble for inspection and replace parts.

Oil leakage of plunger sleeve or oil pan

Sand hole of casting

Replace casting


Other oil leaks from the contact surface with the housing and the end surface of the output shaft

The rubber sealing ring is damaged or aged

Replace rubber sealing ring


The oil seal is damaged or its spring falls off and is aged, the bearing is worn, and the shaft runout is large


1. Replace the oil seal 2. Adjust the clearance or replace the bearing


Abnormal noise


1. The connecting rod and the bearing sleeve bite or damage 2. The snap ring is broken and the bearing bites. 3. Coupling misalignment 4. External vibration 5. Noise of other Hydraulic Systems


1. Replace the parts, check the bearing on the thrust seat for damage and clearance, and correct. 2. Check and correct the coaxiality of the coupling connected to the motor. 3. Correct coaxiality 4. Take anti vibration measures 5. Check the system and eliminate it.

MCB195/MCB530 Series Kawasaki Shaft With Flow Motor

MCB195/MCB530 Series Kawasaki Shaft With Flow Motor

Temperature rise too fast


1. Insufficient system cooling 2. Serious wear of main parts


Check and improve. Same as troubleshooting in fault 4


Fault causes and troubleshooting instructions for ordering:


1 the user can select motors of different specifications according to the working requirements of the host. When ordering, please indicate the product model, quantity, delivery date and destination. You can send a letter or fax.

2 if there are special requirements for installation and connection dimensions, please contact our company to handle relevant procedures when ordering.


Tag: hydraulic motors

Random Recommend

  • How to maintain a hydraulic system
  • Hydraulic Bolt Torquing Machines: Precision Fastening Solutions for Industrial Applications
  • Ultimate Guide to How Torque Wrenches Work
  • A Comprehensive Guide To Extending Planetary Gearboxes Lifespan
  • Single-Acting vs. Double-Acting Hydraulic Hand Pumps: Which One is Right for You
  • Bolting Safety Revolutionized: Washer System Eliminates Hand Injuries
  • A Guide to Hydraulic Power Unit Selection and Installation
  • What are the causes of noise in the hydraulic system?
  • How to Troubleshoot and Fix Slow Hydraulic Motor Speed
  • Types of Flow Control Valves

Related Products

Sauer Danfoss Series Hydraulic Pump PV42 Parts With  Spare Parts Repair Kit

Sauer Danfoss Series Hydraulic Pump PV42 Parts With Spare Parts Repair Kit

​Kawasaki K7V63 Hydraulic Pump Parts

​Kawasaki K7V63 Hydraulic Pump Parts

Multifunctional Battery Powered Crimping Tool

Multifunctional Battery Powered Crimping Tool

Rexroth Series Hydraulic Pump A2FM Parts With  Spare Parts Repair Kit

Rexroth Series Hydraulic Pump A2FM Parts With Spare Parts Repair Kit

SQP2  Replace Tokimec SQP Lower Noise Hydraulic Vane Pump

SQP2 Replace Tokimec SQP Lower Noise Hydraulic Vane Pump

P84 Two Speed, Hydraulic Steel Hand Pump,Double-Acting

P84 Two Speed, Hydraulic Steel Hand Pump,Double-Acting

Single acting hydraulic cylinder for snowplow

Single acting hydraulic cylinder for snowplow

FS109, 10 Ton Hydraulic Flange Spreader

FS109, 10 Ton Hydraulic Flange Spreader

R01,R02, R04, R05, R06 R012 Series Pump Head

R01,R02, R04, R05, R06 R012 Series Pump Head

110 Volt Electric Pump For Small Hydraulic Tools

110 Volt Electric Pump For Small Hydraulic Tools

  • ABOUT US

    • Honor
    • Manufacturing Capacity
    • Privacy Policy
    • Terms of Service
    • FAQ
  • PRODUCTS

    • Hydraulic Pumps
    • Hydraulic Motors
    • Hydraulic Valves
    • Planetary Gearboxes
    • Hydraulic Cylinder
    • Hydraulic Power Units
    • Hydraulic Pump Parts
    • Hydraulic Tools
    • Hydraulic System
    • Hydraulic Manifolds
    • Hydraulic Winch
    • Electro Hydraulic Actuators
  • APPLICATIONS

    • MOBILE
    • AGRICULTURE
    • INDUSTRIAL
    • ENERGY
    • FOOD & BEVERAGE
    • OIL & GAS
  • CONTACT US

    NO. 626 Yuncai Road,

    Yunlong Town, Yinzhou,

    Ningbo, Zhejiang, China.

    +86-574-88188161
    +8613905748980

    Monday - Friday:

    8:30 AM to 5:30 PM

    seo1@saivs.com

    Saivs industrial twitter youtube linkedin pinterest
Copyright © 2012-2025 Ningbo Saivs Machinery Co.,ltd. 
TAGS  SiteMap