SAIVS
  • HOME
  • ABOUT US
    • Honor
    • Manufacturing Capacity
    • Privacy Policy
    • Terms of Service
    • FAQ
  • PRODUCTS
    • Hydraulic Pumps
      • Rexroth
        • A2F Series
        • A4 F/V Series
        • A7VO Series
        • A8VO Series
        • A10V Series
        • A11V Series
        • PG Series
        • AZ Series
        • PV Series
      • Parker
        • PV-plus Series
        • P1 PD Series
        • PAVC Series
        • VP1 Series
        • PG Series
        • P2 P3 Series
      • Sauer-Danfoss
        • 45 Series
        • 90 Series
      • Eaton Vickers
        • PVM Series
        • PVH Series
        • PVQ Series
        • PVE Series
        • VMQ Series
      • Nachi
        • PVD Series
        • PVK Series
        • PVS Series
        • PZS Series
        • PZ Series
      • Hawe
        • V30 Series
        • V60N Series
      • Kawasaki
        • K3V Series
        • K5V Series
      • Sumitomo
        • QT Series
      • Linde
        • MPR Series
        • HPV-02 Series
        • HPR-02 Series
      • Vane Pumps
      • Gear Pumps
    • Hydraulic Motors
      • SAI GM Series Motor
      • Intermot Piston Motor
      • Hydraulic Cycloidal Motors
      • Rexroth Hydraulic Motor
      • Poclain Hydraulic Motor
    • Hydraulic Valves
      • Pressure Relay
      • Pressure Valve
      • Threaded Cartridge Valve
      • Flow Valve
      • Anti-explosion Valve
      • Proportional servo valve
      • Direction Valve
      • Directional Control Valves
    • Planetary Gearboxes
      • Rexroth
      • Bonfiglioli
      • Brevini
      • Dinamicoil
      • O&K
    • Hydraulic Cylinder
      • Aerial Work Platforms
      • Agricultural Equipment
      • Construction Equipment
      • Manufacturing Equipment
      • Marine
      • Material Handling
      • Mining
      • Road Service
      • Waste/Recycling
      • Cylinder Parts
    • Hydraulic Power Units
      • Scissor High Altitude Platform
      • Pallet Car
      • The Wing Car
      • Lift Platform
      • Automobile Tail Plate
      • Special Vehicle
    • Hydraulic Pump Parts
      • Parker Series
      • Komatsu Excavator Series
      • Hitachi Series
      • Rexroth Series
      • Sauer Danfoss Series
      • Uchida Series
      • Messori Series
      • Kayaba Series
      • Toshiba Series
      • Nachi Series
      • Eaton Vickers Series
      • Linde Series
      • Caterpillar Series
      • Kawasaki Series
      • Kobelco/Kato Series
      • Hawe Series
      • Sumitomo Series
    • Hydraulic Tools
      • Flange Tools
      • Hydraulic Lifting tools
        • Hydraulic pump
        • Hydraulic Cylinder/Jack
        • Hydraulic Professional Tools
      • Bolting Tools
        • Hydraulic Tensioners
        • Hydraulic Torque Wrench Pumps
        • Torque wrenches
      • Hydraulic Components
      • Electric Power Tools
    • Hydraulic System
    • Hydraulic Manifolds
    • Hydraulic Winch
    • Electro Hydraulic Actuators
  • APPLICATIONS
    • MOBILE
    • AGRICULTURE
    • INDUSTRIAL
    • ENERGY
    • FOOD & BEVERAGE
    • OIL & GAS
  • DOWNLOAD
    • Best PDF
  • CONTACT US
  • BLOG
HOME > BLOG

Common problems with hydraulic cylinders

Author:SAIVS Time:2023-02-10 Click:

002--.jpg

A complete Hydraulic System consists of four parts: power unit, actuating device, control and adjustment device. It is self-evident that the Hydraulic Cylinder of auxiliary device plays an important role as the main power actuating element. We are going to discuss some minor issues that may arise after a while.

1. Hydraulic cylinder controls oil temperature to prevent seal from deteriorating

An important reason for premature deterioration of seals is the high oil temperature. In most cases, when the oil temperature often exceeds, the oil viscosity will greatly decrease, the expansion and aging of the sealing ring will fail, resulting in leakage of the hydraulic system. According to studies, the life of the seal will be halved whenever the oil temperature rises.

Therefore, the oil temperature should be controlled within the following. For this purpose, the oil outlet pipe inside the tank should be separated from the oil return pipe by a baffle, so as to reduce the distance between the tank and the cylinder or motor of the actuator. The right angle elbow should be used as little as possible in the pipeline. In addition, the compatibility of the oil with the sealing material should be paid attention to.

2. Hydraulic cylinder should assemble sealing ring correctly.

When assembling sealing ring, it should be oiled on its surface. If it has to pass through the opening such as keyway thread on the shaft, guide tool should be used instead of metal tool such as screwdriver.

Otherwise, oil leakage may occur due to scratches on the sealing ring. For directional sealing rings such as the equal-type sealing ring, the lip should be facing the pressure oil chamber when assembling. Pay attention to protecting the lip from scratches such as sharp edges and burrs of parts. Before installing the combined seal, place the seal in hydraulic oil and boil it to a certain temperature, special guide sleeve and collecting tool should be used when installing.

Snowplow Hydraulic Cylinders

Snowplow Hydraulic Cylinders

3. Hydraulic cylinder must be reasonably designed to prevent oil leakage from static seal

The dimensions and tolerances of the sealing grooves of the static seals allow the installed static seals to be extruded and deformed to fill the micro-recesses on the mating surfaces and to increase the stress in the seals above the pressure being sealed.

When part rigidity or bolt pretension force is not enough, the mating surface will separate under the action of hydraulic pressure and cause excessive clearance. With the movement of mating surface, static seal becomes dynamic seal.

4. Reasonable Design and Processing of Sealing Grooves for Hydraulic Cylinders

The design or fabrication of the sealing groove in the hydraulic cylinder is a prerequisite for reducing leakage and preventing premature damage of the oil seal if the groove size in the static seal between the piston and piston rod is too small for the sealing ring to move within the groove.

The bottom of the sealing ring will be damaged by reaction force and result in leakage. The design of oil seal groove is mainly based on the structural shape, dimensional tolerance of groove position and roughness of sealing surface.


Tag: hydraulic cylinders hydraulic system

Random Recommend

  • What is Electrohydraulic Servo Valve?
  • Internal Gear Pumps: A Complete Overview
  • Hydraulic cylinder manufacturing
  • What factors should be considered when selecting a Parker piston pump?
  • Application and Development of Hydraulic Technology in Agriculture
  • Log No. 6 Sun Hydraulic Valves To South Africa Customers
  • Preventing Hydraulic Oil Pollution
  • special pump with hydraulic torque wrench
  • Log No. 10: Electric Hydraulic Torque Wrench Pump To Moldova Customers
  • What are the selection criteria for hydraulic motors?

Related Products

SUN CBCALAN hydraulics Cartridge valve

SUN CBCALAN hydraulics Cartridge valve

2-500 Nm Plug-In Torque Wrench,MTE-1 Series

2-500 Nm Plug-In Torque Wrench,MTE-1 Series

SNC Series High Pressure Capacity Hydraulic Nut Split Broker Splitter

SNC Series High Pressure Capacity Hydraulic Nut Split Broker Splitter

SSJ Series Single-Acting High Tonnage Hydraulic Cylinders

SSJ Series Single-Acting High Tonnage Hydraulic Cylinders

High-Quality Hydraulic Torque Wrench for Precise Bolt Tightening

High-Quality Hydraulic Torque Wrench for Precise Bolt Tightening

Champagne,SBT Series Square Drive Hydraulic Torque Wrench

Champagne,SBT Series Square Drive Hydraulic Torque Wrench

A10VGT Rexroth Hydraulic pump 071 090 115

A10VGT Rexroth Hydraulic pump 071 090 115

HPV050/102/118

HPV050/102/118

Sauer Danfoss Series 45 Open Circuit Axial Piston Pumps

Sauer Danfoss Series 45 Open Circuit Axial Piston Pumps

HPE-4,Gasoline Engine Hydraulic Pump

HPE-4,Gasoline Engine Hydraulic Pump

  • ABOUT US

    • Honor
    • Manufacturing Capacity
    • Privacy Policy
    • Terms of Service
    • FAQ
  • PRODUCTS

    • Hydraulic Pumps
    • Hydraulic Motors
    • Hydraulic Valves
    • Planetary Gearboxes
    • Hydraulic Cylinder
    • Hydraulic Power Units
    • Hydraulic Pump Parts
    • Hydraulic Tools
    • Hydraulic System
    • Hydraulic Manifolds
    • Hydraulic Winch
    • Electro Hydraulic Actuators
  • APPLICATIONS

    • MOBILE
    • AGRICULTURE
    • INDUSTRIAL
    • ENERGY
    • FOOD & BEVERAGE
    • OIL & GAS
  • CONTACT US

    NO. 626 Yuncai Road,

    Yunlong Town, Yinzhou,

    Ningbo, Zhejiang, China.

    +86-574-88188161
    +8613905748980

    Monday - Friday:

    8:30 AM to 5:30 PM

    seo1@saivs.com

    Saivs industrial twitter youtube linkedin pinterest
Copyright © 2012-2024 Ningbo Saivs Machinery Co.,ltd. 
TAGS  SiteMap